玩客云添加USB优先启动命令
setenv bootfromrecovery 0
setenv bootfromnand 0
setenv start_mmc_autoscript 'if fatload mmc 0 11000000 s805_autoscript; then autoscr 11000000; fi;'
setenv start_usb_autoscript "if fatload usb 0 11000000 s805_autoscript; then autoscr 11000000; fi; if fatload usb 1 11000000 s805_autoscript; then autoscr 11000000; fi;"
setenv start_autoscript 'if usb start; then run start_usb_autoscript; fi; if mmcinfo; then run start_mmc_autoscript; fi;'
setenv bootcmd 'run start_autoscript; run storeboot'
setenv firstboot 1
saveenv
如果为Armbian官方仓库编译的镜像则为以下内容
[admonition title="注意" color="blue"]#之后的一行内容仅为注释，并不需要在终端中运行！[/admonition]
setenv bootfromrecovery 0
setenv bootfromnand 0
# set a script called start_mmc_autoscript, which tries to load boot.scr from mmc 0 first, if failed, then from mmc 1
setenv start_mmc_autoscript 'if fatload mmc 0 11000000 boot.scr; then autoscr 11000000; fi; if fatload mmc 1 11000000 boot.scr; then autoscr 11000000; fi;'
# set a script called start_usb_autoscript, which tries to load boot.scr from usb 0 first, if failed, then from usb 1
setenv start_usb_autoscript "if fatload usb 0 11000000 boot.scr; then autoscr 11000000; fi; if fatload usb 1 11000000 boot.scr; then autoscr 11000000; fi;"
# set a script called start_autoscript, which checks if any usb device is connected. If so, call start_usb_autoscript; otherwise, call start_mmc_autoscript
setenv start_autoscript 'if usb start; then run start_usb_autoscript; fi; if mmcinfo 1; then run start_mmc_autoscript; fi;'
setenv bootcmd 'run start_autoscript; run storeboot'
setenv firstboot 1
saveenv
X96 Max+在linux下安装GPU驱动（转载由[S905X3] GPU Acceleration with bifrost is really possible in wayland? - General Chat - Armbian Community Forums）
[admonition title="注意" color="blue"]#之后的一行内容仅为注释，并不需要在终端中运行！[/admonition]
#install ubuntu desktop
sudo apt update
sudo apt install ubuntu-desktop
# add mesa master ppa (https://launchpad.net/~oibaf/+archive/u ... cs-drivers)
sudo add-apt-repository ppa:oibaf/graphics-drivers
sudo apt upgrade
#Then set panfrost drive in enviroment
sudo sh -c "echo 'PAN_MESA_DEBUG=bifrost' >> /etc/environment"
#reboot
sudo reboot
#after boot set in the GDM wayland and panfrost should be working
群晖用户重置密码
sudo synouser --setpw username password
群晖wp-config.php添加代码（在第86行）
define('FS_METHOD', 'direct');
Ubuntu 20.04 Official Repository List (sources.list)
deb http://archive.ubuntu.com/ubuntu/ focal main restricted universe multiverse
deb-src http://archive.ubuntu.com/ubuntu/ focal main restricted universe multiverse
deb http://archive.ubuntu.com/ubuntu/ focal-updates main restricted universe multiverse
deb-src http://archive.ubuntu.com/ubuntu/ focal-updates main restricted universe multiverse
deb http://archive.ubuntu.com/ubuntu/ focal-security main restricted universe multiverse
deb-src http://archive.ubuntu.com/ubuntu/ focal-security main restricted universe multiverse
deb http://archive.ubuntu.com/ubuntu/ focal-backports main restricted universe multiverse
deb-src http://archive.ubuntu.com/ubuntu/ focal-backports main restricted universe multiverse
deb http://archive.canonical.com/ubuntu focal partner
deb-src http://archive.canonical.com/ubuntu focal partner
Windows XP x64 Edition key
B2RBK-7KPT9-4JP6X-QQFWM-PJD6G
VMware AMD安装macOS
smc.version = "0"
cpuid.0.eax = "0000:0000:0000:0000:0000:0000:0000:1011"
cpuid.0.ebx = "0111:0101:0110:1110:0110:0101:0100:0111"
cpuid.0.ecx = "0110:1100:0110:0101:0111:0100:0110:1110"
cpuid.0.edx = "0100:1001:0110:0101:0110:1110:0110:1001"
cpuid.1.eax = "0000:0000:0000:0001:0000:0110:0111:0001"
cpuid.1.ebx = "0000:0010:0000:0001:0000:1000:0000:0000"
cpuid.1.ecx = "1000:0010:1001:1000:0010:0010:0000:0011"
cpuid.1.edx = "0000:0111:1000:1011:1111:1011:1111:1111"
smbios.reflectHost = "TRUE"
hw.model = "MacBookPro14,3"
board-id = "Mac-551B86E5744E2388"
keyboard.vusb.enable = "TRUE"
mouse.vusb.enable = "TRUE"
TQC DTS
折叠
展开 / 收起
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
// Copyright (C) 2019 Ondřej Jirman <megous@megous.com>
/dts-v1/;
#include "sun50i-h6.dtsi"
#include "sun50i-h6-cpu-opp.dtsi"
#include <dt-bindings/gpio/gpio.h>
/ {
model = "TQC A01";
compatible = "taiqigame,tqc-a01", "allwinner,sun50i-h6";
aliases {
ethernet0 = &emac;
serial0 = &uart0;
serial1 = &uart1;
};
chosen {
stdout-path = "serial0:115200n8";
};
connector {
compatible = "hdmi-connector";
ddc-en-gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */
type = "a";
port {
hdmi_con_in: endpoint {
remote-endpoint = <&hdmi_out_con>;
};
};
};
ext_osc32k: ext_osc32k_clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
clock-output-names = "ext_osc32k";
};
leds {
compatible = "gpio-leds";
led-0 {
label = "orangepi:blue:power";
gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
default-state = "on";
};
};
reg_vcc5v: vcc5v {
/* board wide 5V supply directly from the DC jack */
compatible = "regulator-fixed";
regulator-name = "vcc-5v";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-always-on;
};
reg_vcc33_wifi: vcc33-wifi {
/* Always on 3.3V regulator for WiFi and BT */
compatible = "regulator-fixed";
regulator-name = "vcc33-wifi";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
vin-supply = <®_vcc5v>;
};
reg_vcc_wifi_io: vcc-wifi-io {
/* Always on 1.8V/300mA regulator for WiFi and BT IO */
compatible = "regulator-fixed";
regulator-name = "vcc-wifi-io";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
vin-supply = <®_vcc33_wifi>;
};
wifi_pwrseq: wifi-pwrseq {
compatible = "mmc-pwrseq-simple";
clocks = <&rtc 1>;
clock-names = "ext_clock";
reset-gpios = <&r_pio 0 8 GPIO_ACTIVE_LOW>; /* PL8 */
post-power-on-delay-ms = <200>;
};
};
&ac200_ephy {
status = "okay";
};
&ac200_pwm_clk {
status = "okay";
};
&cpu0 {
cpu-supply = <®_dcdca>;
};
&de {
status = "okay";
};
&dwc3 {
status = "okay";
};
&ehci0 {
status = "okay";
};
&ehci3 {
status = "okay";
};
&emac {
pinctrl-names = "default";
pinctrl-0 = <&ext_rmii_pins>;
phy-mode = "rmii";
phy-handle = <&ext_rmii_phy>;
status = "okay";
};
&gpu {
mali-supply = <®_dcdcc>;
status = "okay";
};
&hdmi {
status = "okay";
};
&hdmi_out {
hdmi_out_con: endpoint {
remote-endpoint = <&hdmi_con_in>;
};
};
&i2c3 {
status = "okay";
};
&mdio {
ext_rmii_phy: ethernet-phy@1 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <1>;
};
};
&mmc0 {
vmmc-supply = <®_cldo1>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
bus-width = <4>;
status = "okay";
};
&mmc1 {
vmmc-supply = <®_vcc33_wifi>;
vqmmc-supply = <®_vcc_wifi_io>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
non-removable;
status = "okay";
brcm: sdio-wifi@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
interrupt-parent = <&r_pio>;
interrupts = <1 0 IRQ_TYPE_LEVEL_LOW>; /* PM0 */
interrupt-names = "host-wake";
};
};
&mmc2 {
vmmc-supply = <®_cldo1>;
vqmmc-supply = <®_bldo2>;
cap-mmc-hw-reset;
non-removable;
bus-width = <8>;
status = "okay";
};
&ohci0 {
status = "okay";
};
&ohci3 {
status = "okay";
};
&pio {
vcc-pc-supply = <®_bldo2>;
vcc-pd-supply = <®_cldo1>;
vcc-pg-supply = <®_vcc_wifi_io>;
};
&r_rsb {
status = "okay";
axp805: pmic@745 {
compatible = "x-powers,axp805", "x-powers,axp806";
reg = <0x745>;
interrupt-parent = <&r_intc>;
interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>;
interrupt-controller;
#interrupt-cells = <1>;
x-powers,self-working-mode;
vina-supply = <®_vcc5v>;
vinb-supply = <®_vcc5v>;
vinc-supply = <®_vcc5v>;
vind-supply = <®_vcc5v>;
vine-supply = <®_vcc5v>;
aldoin-supply = <®_vcc5v>;
bldoin-supply = <®_vcc5v>;
cldoin-supply = <®_vcc5v>;
regulators {
reg_aldo1: aldo1 {
regulator-always-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-pl-led-ir";
};
reg_aldo2: aldo2 {
regulator-always-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc33-audio-tv-ephy-mac";
};
/* ALDO3 is shorted to CLDO1 */
reg_aldo3: aldo3 {
regulator-always-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc33-io-pd-emmc-sd-usb-uart-1";
};
reg_bldo1: bldo1 {
regulator-always-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-name = "vcc18-dram-bias-pll";
};
reg_bldo2: bldo2 {
regulator-always-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-name = "vcc-efuse-pcie-hdmi-pc";
};
bldo3 {
/* unused */
};
bldo4 {
/* unused */
};
reg_cldo1: cldo1 {
regulator-always-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc33-io-pd-emmc-sd-usb-uart";
};
cldo2 {
/* unused */
};
cldo3 {
/* unused */
};
reg_dcdca: dcdca {
regulator-always-on;
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <1160000>;
regulator-ramp-delay = <2500>;
regulator-name = "vdd-cpu";
};
reg_dcdcc: dcdcc {
regulator-enable-ramp-delay = <32000>;
regulator-min-microvolt = <810000>;
regulator-max-microvolt = <1080000>;
regulator-ramp-delay = <2500>;
regulator-name = "vdd-gpu";
};
reg_dcdcd: dcdcd {
regulator-always-on;
regulator-min-microvolt = <960000>;
regulator-max-microvolt = <960000>;
regulator-name = "vdd-sys";
};
reg_dcdce: dcdce {
regulator-always-on;
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-name = "vcc-dram";
};
sw {
/* unused */
};
};
};
};
&pwm {
status = "okay";
};
&r_ir {
status = "okay";
};
&rtc {
clocks = <&ext_osc32k>;
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_ph_pins>;
status = "okay";
};
/* There's the BT part of the AP6256 connected to that UART */
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
uart-has-rtscts;
status = "okay";
bluetooth {
compatible = "brcm,bcm4345c5";
clocks = <&rtc 1>;
clock-names = "lpo";
device-wakeup-gpios = <&r_pio 1 2 GPIO_ACTIVE_HIGH>; /* PM2 */
host-wakeup-gpios = <&r_pio 1 1 GPIO_ACTIVE_HIGH>; /* PM1 */
shutdown-gpios = <&r_pio 1 4 GPIO_ACTIVE_HIGH>; /* PM4 */
max-speed = <1500000>;
};
};
&usb2otg {
/*
* This board doesn't have a controllable VBUS even though it
* does have an ID pin. Using it as anything but a USB host is
* unsafe.
*/
dr_mode = "host";
status = "okay";
};
&usb2phy {
usb0_id_det-gpios = <&pio 2 15 GPIO_ACTIVE_HIGH>; /* PC15 */
usb0_vbus-supply = <®_vcc5v>;
usb3_vbus-supply = <®_vcc5v>;
status = "okay";
};
&usb3phy {
status = "okay";
};
Sakurairo HTML锚点 不打开新页面
class="toc-link" target="_self"
Windows清除桌面图标缓存
rem 关闭Windows外壳程序explorer
taskkill /f /im explorer.exe
rem 清理系统图标缓存数据库
attrib -h -s -r "%userprofile%\AppData\Local\IconCache.db"
del /f "%userprofile%\AppData\Local\IconCache.db"
attrib /s /d -h -s -r "%userprofile%\AppData\Local\Microsoft\Windows\Explorer\*"
del /f "%userprofile%\AppData\Local\Microsoft\Windows\Explorer\thumbcache_32.db"
del /f "%userprofile%\AppData\Local\Microsoft\Windows\Explorer\thumbcache_96.db"del /f "%userprofile%\AppData\Local\Microsoft\Windows\Explorer\thumbcache_102.db"del /f "%userprofile%\AppData\Local\Microsoft\Windows\Explorer\thumbcache_256.db"del /f "%userprofile%\AppData\Local\Microsoft\Windows\Explorer\thumbcache_1024.db"del /f "%userprofile%\AppData\Local\Microsoft\Windows\Explorer\thumbcache_idx.db"del /f "%userprofile%\AppData\Local\Microsoft\Windows\Explorer\thumbcache_sr.db"
rem 清理 系统托盘记忆的图标
echo y|reg delete "HKEY_CLASSES_ROOT\Local Settings\Software\Microsoft\Windows\CurrentVersion\TrayNotify" /v IconStreams
echo y|reg delete "HKEY_CLASSES_ROOT\Local Settings\Software\Microsoft\Windows\CurrentVersion\TrayNotify" /v PastIconsStream
rem 重启Windows外壳程序explorer
start explorer
rem 重启Windows外壳程序explorer
start explorer
vscode略去调试信息
"miDebuggerArgs": "-q -ex quit; wait() { fg >/dev/null; }; /bin/gdb -q --interpreter=mi",
PHP程序502
将request_terminate_timeout调大
黑群晖激活ABB
DSM6.X
https://群晖ip地址:https端口号/webapi/auth.cgi?api=SYNO.API.Auth&method=Login&version=1&account=群晖本地用户名&passwd=群晖本地密码
https://群晖ip地址:https端口号/webapi/entry.cgi?api=SYNO.ActiveBackup.Activation&method=set&version=1&activated=true&serial_number="群晖的SN码"
DSM7.X
https://群晖ip地址:https端口号/webapi/auth.cgi?api=SYNO.API.Auth&version=3&method=login&account=管理员用户名&passwd=密码&format= cookie
https://群晖ip地址:https端口号/webapi/entry.cgi?api=SYNO.ActiveBackup.Activation&method=set&version=1&activated=true&serial_number="序列号"
